SOIL EQUIPMENT ( Lab. Uji Mekanika Tanah / Mektan)
¤ SO-110A HAND BOR
¤ SO-130A STANDARD PENETRATION TEST ( ASTM D-1586; AASHTO T-206)
¤ SO-140 SAMPLE EXTRUDER
¤ SO-145 SAMPLE EXTRUDER, Electric
¤ SO-150 DYNAMIC CONE PENETROMETER ( DCP)
¤ SO-160 TUBE DENSITY SAMPLER ( ASTM D-2573)
¤ SO-170 CORPS OF ENGINEER SOIL SURFACE SAMPLER ( ASTM D-2937)
¤ SO-200 DUTCH CONE PENETROMETER / Sondir 2.5 Ton ( ASTM D-3441)
¤ SO-210 DUTCH CONE PENETROMETER / Sondir 5 Ton ( ASTM D-3441)
¤ SO-200HD HYDRAULIC CONE PENETROMETER / Sondir Hydraulic 2.5 Ton ( ASTM D-3441)
¤ SO-210HD HYDRAULIC CONE PENETROMETER / Sondir Hydraulic 5 Ton ( ASTM D-3441)
¤ SO-700HD HYDRAULIC CONE PENETROMETER / Sondir Hydraulic 10 Ton ( ASTM D-3441)
¤ SO-250 PLATE BEARING TEST SET ( ASTM D-1194; AASHTO T-235)
¤ SO-260 FIELD CBR TEST SET ( ASTM D-4429)
¤ SO-270 PROVING RING PENETROMETER
¤ SO-280 TVA PENETROMETER
¤ ATTERBERGH LIMIT ( SO-310, SO-315, SO-320)
¤ SO-310 LIQUID LIMIT TEST SET ( ASTM D-4318; AASHTO T-89)
¤ SO-311A LIQUID LIMIT DEVICE, Hand Operated, ( ASTM D-4318; AASHTO T-89)
¤ SO-311B LIQUID LIMIT DEVICE, Electric, ( ASTM D-4318; AASHTO T-89)
¤ SO-315 PLASTIC LIMIT TEST SET ( ASTM D-4318; AASHTO T-90)
¤ SO-320 SHRINKAGE LIMIT TEST SET ( ASTM D-427; AASHTO T-92)
¤ SO-330A HYDROMETER ANALYSIS TEST SET ( ASTM D-422; AASHTO T-88)
¤ SO-338 MECHANICAL END OVER END SHAKER ( BS-1377)
¤ SO-339A VACUUM STAND, With 6 Flask Capacity.
¤ SO-340 SPECIFIC GRAVITY, Heating Method
¤ SO-340A SPECIFIC GRAVITY, Vacuum Method ( ASTM D-854; AASHTO T-100)
¤ SO-340B SPECIFIC GRAVITY, Vacuum Method ( ASTM D-854; AASHTO T-100)
¤ SO-350 COMPACTION TEST SET ( ASTM D-698/ D-1557; T-99/ T-180)
¤ SO-360A LABORATORY CBR TEST SET, Electric ( ASTM D-1883; AASHTO T-193)
¤ SO-360B LABORATORY CBR TEST SET ( ASTM D-1883; AASHTO T-193)
¤ SO-370 COMBINATION PERMEAMETER ( ASTM D-2434 / AASHTO T-215)
¤ SO-390A COMPACTION PERMEAMETER TEST SET ( 1/ 30 cu.ft)
¤ SO-395A COMPACTION PERMEAMETER TEST SET ( 1/ 13.33 cu.ft)
¤ SO-400 SAND CONE TEST SET ( ASTM D-1556 / AASHTO T-191)
¤ SO-430 SPEEDY MOISTURE TESTER ( AASHTO T-217)
¤ SO-450 MOISTURE CONTENT TEST SET
¤ SO-500 UNCONFINED COMPRESSION MACHINE ( ASTM D-2166; AASHTO T-208)
¤ SO-500A UNCONFINED COMPRESSION MACHINE ( ASTM D-2166; AASHTO T-208)
¤ SO-515 CONSOLIDATION TEST SET ( ASTM D-2435; AASHTO T-216)
¤ SO-525 DIRECT SHEAR TEST SET ( ASTM D-3080; AASHTO T-236)
SO-600 TRIAXIAL TEST SET - UU, CU, CD ( Digital Pore Pressure Measuring)
ASTM D-2850
AGGREGATE EQUIPMENT ( Lab. Uji Bahan / Mektan)
¤ AG-100 SAMPLE SPLITER 1/ 2 " ( 12 holes, 1/ 2 inch chute width)
¤ AG-101 SAMPLE SPLITER 3/ 4 " ( 12 holes, 3/ 4 inch chute width)
¤ AG-102 SAMPLE SPLITER 1 " ( 12 holes, 1 inch chute width)
¤ AG-103 SAMPLE SPLITER 1-1/ 2 " ( 12 holes, 1-1/ 2 inch chute width)
¤ AG-104 SAMPLE SPLITER 2 " ( 12 holes, 2 inch chute width)
¤ AG-105 SAMPLE SPLITER 2 1/ 2 " ( 12 holes, 2 1/ 2 inch chute width)
¤ AG-106 SAMPLE SPLITER 3 " ( 12 holes, 3 inch chute width)
¤ AG-111 GILSON SAMPLE SPLITTER ( Varieble chute width, 1/ 2 " increment)
¤ AG-122 PRECISSION SAMPLE SPLITTER ( chute width 1/ 4 " x 32 holes)
¤ AG-123 PRECISSION SAMPLE SPLITTER ( chute width 1/ 4 " x 16 holes)
¤ AG-170 LENGTH GAUGE ( BS-812)
¤ AG-180 THICKNESS GAUGE ( BS-812)
¤ STANDAR SIEVE ( Brass Round Sieve 8 inch Diameter)
Sieve Analysis - Gradation Test
AG-200A SIEVE 4 " ; mesh 101.6 mm opening, 8 inch dia.
AG-201A SIEVE 3 1/ 2 " ; mesh 88.9 mm opening, 8 inch dia.
AG-202A SIEVE 3 " ; mesh 76.2 mm opening, 8 inch dia.
AG-203A SIEVE 2 1/ 2 " ; mesh 62.5 mm opening, 8 inch dia.
AG-204A SIEVE 2 " ; mesh 50.8 mm opening, 8 inch dia.
AG-205A SIEVE 1 3/ 4 " ; mesh 44.4 mm opening, 8 inch dia.
AG-206A SIEVE 1 1/ 2 " ; mesh 38.1 mm opening, 8 inch dia.
AG-207A SIEVE 1 1/ 4 " ; mesh 31.7 mm opening, 8 inch dia.
AG-208A SIEVE 1 " ; mesh 25.4 mm opening, 8 inch dia.
AG-209A SIEVE 7/ 8 " ; mesh 22.2 mm opening, 8 inch dia.
AG-210A SIEVE 3/ 4 " ; mesh 19.0 mm opening, 8 inch dia.
AG-211A SIEVE 5/ 8 " ; mesh 15.8 mm opening, 8 inch dia.
AG-212A SIEVE 1/ 2 " ; mesh 12.7 mm opening, 8 inch dia.
AG-213A SIEVE 7/ 16 " ; mesh 11.1 mm opening, 8 inch dia.
AG-214A SIEVE 3/ 8 " ; mesh 9.5 mm opening, 8 inch dia.
AG-215A SIEVE 5/ 16 " ; mesh 7.9 mm opening, 8 inch dia.
AG-216A SIEVE 1/ 4 " ; mesh 6.3 mm opening, 8 inch dia.
AG-218A SIEVE # 4; mesh 4.75 mm opening, 8 inch dia.
AG-222A SIEVE # 8; mesh 2.36 mm opening, 8 inch dia.
AG-223A SIEVE # 10; mesh 2.00 mm opening, 8 inch dia.
AG-224A SIEVE # 12; mesh 1.70 mm opening, 8 inch dia.
AG-226A SIEVE # 16; mesh 1.18 mm opening, 8 inch dia.
AG-228A SIEVE # 20; mesh 0.850 mm opening, 8 inch dia.
AG-230A SIEVE # 30; mesh 0.600 mm opening, 8 inch dia.
AG-232A SIEVE # 40; mesh 0.425 mm opening, 8 inch dia.
AG-234A SIEVE # 50; mesh 0.300 mm opening, 8 inch dia.
AG-235A SIEVE # 60; mesh 0.250 mm opening, 8 inch dia.
AG-236A SIEVE # 70; mesh 0.212 mm opening, 8 inch dia.
AG-237A SIEVE # 80; mesh 0.180 mm opening, 8 inch dia.
AG-238A SIEVE # 100; mesh 0.150 mm opening, 8 inch dia.
AG-239A SIEVE # 120; mesh 0.125 mm opening, 8 inch dia.
AG-240A SIEVE # 140; mesh 0.106 mm opening, 8 inch dia.
AG-241A SIEVE # 170; mesh 0.090 mm opening, 8 inch dia.
AG-242A SIEVE # 200; mesh 0.075 mm opening, 8 inch dia.
AG-250 PAN & COVER; receiver with lid, 8 inch dia,
¤ STANDAR SIEVE ( Stainlles Steel Round Sieve 8 inch Diameter)
Sieve Analysis - Gradation Test - AG 300A up to AG 350)
¤ AG-510 SIEVE SHAKER
¤ AG-515 SIEVE SHAKER, Electric
¤ WOODEN STANDAR SIEVE ( Stainlles Steel Round Sieve 8 inch Diameter)
AG-400 WOODEN SIEVE 4 " - mesh 101.6 mm opening
AG-401 WOODEN SIEVE 3 1/ 2 " - mesh 88.9 mm opening
AG-402 WOODEN SIEVE 3 " - mesh 76.2 mm opening
AG-403 WOODEN SIEVE 2 1/ 2 " - mesh 62.5 mm opening
AG-404 WOODEN SIEVE 2 " - mesh 50.8 mm opening
AG-405 WOODEN SIEVE 1 3/ 4 " - mesh 44.4 mm opening
AG-406 WOODEN SIEVE 1 1/ 2 " , mesh 38.1 mm opening
AG-407 WOODEN SIEVE 1 1/ 4 " , mesh 31.7 mm opening
AG-408 WOODEN SIEVE 1 " , mesh 25.4 mm opening
AG-409 WOODEN SIEVE 7/ 8 " , mesh 22.2 mm opening
AG-410 WOODEN SIEVE 3/ 4 " , mesh 19.0 mm opening
AG-411 WOODEN SIEVE 5/ 8 " , mesh 15.8 mm opening
AG-412 WOODEN SIEVE 1/ 2 " ; mesh 12.7 mm opening
AG-413 WOODEN SIEVE 7/ 16 " ; mesh 11.1 mm opening
AG-414 WOODEN SIEVE 3/ 8 " ; mesh 9.5 mm opening
AG-415 WOODEN SIEVE 5/ 16 " ; mesh 7.9 mm opening
AG-416 WOODEN SIEVE 1/ 4 " ; mesh 6.3 mm opening
AG-418 WOODEN SIEVE # 4; Mesh 4.75 mm opening
¤ AG-492 WET WASHING SIEVE, # 200, 8 " dia., 4 " depth.
¤ AG-493 WET WASHING SIEVE, # 200, 8 " dia., 8 " depth.
¤ AG-600 SAND EQUIVALENT TEST SET ( ASTM D-2419)
¤ AG-610 SAND EQUIVALENT SHAKER ( ASTM D-2419; AASHTO T-176)
¤ AG-621 BOTTLE ROLLER ( BS-812; ASTM C-117)
¤ AG-700 LOS ANGELES ABRASSION MACHINE ( ASTM C-131; AASHTO T-96)
¤ AG-750 AGGREGATE IMPACT TEST ( BS-812)
¤ AG-760 AGGREGATE CRUSHING VALUE APPARATUS ( BS-812)
¤ AG-760A AGGREGATE CRUSHING VALUE APPARATUS
¤ AG-800 BULK DENSITY TEST SET ( ASTM C-29; AASHTO T-19)
¤ AG-810A ABSORPTION OF FINE AGGREGATE TEST SET ( ASTM C-128; AASHTO T-84)
¤ AG-825 SPECIFIC GRAVITY & ABSORPTION OF COARSE AGGREGATE TEST SET, Mechanical Balance ( ASTM C-127; AASHTO T-85)
¤ AG-825 SPECIFIC GRAVITY & ABSORPTION OF COARSE AGGREGATE TEST SET, Digital Balance ( ASTM C-127; AASHTO T-85)
¤ AG-910 ORGANIC IMPURITIES TEST SET ( ASTM C-40; AASHTO T-21)
¤ AG-920 SOUNDNESS TEST SET ( ASTM C-88; AASHTO T-104)
CEMENT EQUIPMENT ( Lab. Uji Bahan / Beton)
¤ CE-100 AIR PERMEABILITY OF PORLAND CEMENT BY FINENESS DEVICE, ( ASTM C-204; AASHTO T-153)
¤ CE-110 SPECIFIC GRAVITY OF HYDRAULIC CEMENT TEST ( ASTM C-188; AASHTO T-133)
¤ CE-120 TIME OF SETTING OF HYDRAULIC CEMENT BY VICAT NEEDLE ( ASTM C-187/ C-191; T-129/ T-131)
¤ CE-160 COMPRESSIVE STRENGTH OF HYDRAULIC CEMENT MORTAR ( ASTM C-109; AASHTO T-106)
¤ CE-160A COMPRESSIVE STRENGTH OF HYDRAULIC CEMENT MORTAR, Electric ( ASTM C-109; AASHTO T-106)
¤ CE-170 COMPRESSION MACHINE 100 kN, Compressive Strength Cement Mortar, ( ASTM C-109)
¤ CE-175 COMPRESSION MACHINE 250 kN, Compressive Strength Cement Mortar, ( ASTM C-109)
CONCRETE EQUIPMENT ( Lab. Uji Beton/ Bahan / Bangunan)
¤ CO-300 CONCRETE CYLINDER MOLD, 10 cm dia x 20 cm height.
¤ CO-301 CONCRETE CYLINDER MOLD, 15 cm dia x 30 cm height.
¤ CO-311 CONCRETE CUBE MOLD, 10 x 10 x 10 cm.
¤ CO-312 CONCRETE CUBE MOLD, 15 x 15 x 15 cm.
¤ CO-317 A CONCRETE BEAM MOLD, 15 x 15 x 60 cm.
¤ CO-319 A CONCRETE BEAM MOLD, 20 x 20 x 80 cm.
¤ CO-321.3 COMPRESSION MACHINE 1500 kN, Hydraulic Hand Pump ( ASTM C-39)
¤ CO-321.4 COMPRESSION MACHINE 2000 kN, Hydraulic Hand Pump ( ASTM C-39)
¤ CO-321.5 COMPRESSION MACHINE 3000 kN, Hydraulic Hand Pump ( ASTM C-39)
¤ CO-325.3 COMPRESSION MACHINE 1500 kN, Electric Hydraulic Pump ( ASTM C-39)
¤ CO-325.4 COMPRESSION MACHINE 2000 kN, Electric Hydraulic Pump ( ASTM C-39)
¤ CO-325.5 COMPRESSION MACHINE 3000 kN, Electric Hydraulic Pump ( ASTM C-39)
¤ CO-330 HYDRAULIC CONCRETE BEAM TESTING MACHINE ( ASTM C-78)
¤ CO-351 MECHANICAL CONCRETE BEAM TESTING MACHINE ( ASTM C-78)
¤ CO-355 COMPACTING FACTOR APPARATUS ( BS-1881)
¤ CO-370 SLUMP TEST SET ( ASTM C-143, AASHTO T-119)
¤ CO-380 VEBE TIME ( BS-1881)
¤ CO-400 AIR CONTENT OF FRESH MIXED CONCRETE ( ASTM C-231, AASHTO T-152)
¤ CO-410 VIBRATING TABLE
¤ CO-470 VERTICAL CYLINDER CAPPING SET ( ASTM C-617)
¤ CO-500 MODULUS OF ELASTICITY IN CONCRETE TEST SET
¤ CO-525 SPLIT TENSILE TEST ( BS-1881)
¤ CO-550 CONCRETE TEST HAMMER ( ASTM C-805)
¤ CO-555 CALIBRATION ANVIL, ( ASTM C-805)
¤ CO-610 LABORATORY CONCRETE MIXER
ASPHALT EQUIPMENT ( Lab. Uji Aspal/ Jalan Raya) .
¤ BI-100 SPECIFIC GRAVITY OF SEMI - SOLID BITUMINOUS MATERIALS ( ASTM D-70, AASHTO T-228)
¤ BI-110 DISTILATION OF CUTBACK ASPHALTS ( ASTM D-402, AASHTO T-78)
¤ BI-120 WATER CONTENT IN PETROLEUM PRODUCTS ( ASTM D-95, AASHTO T-55)
¤ BI-150A SAYBOLT VISCOSIMETER ( ASTM D-402 , AAHSTO T-78)
¤ GE-644.1 ASTM THERMOMETER 17 C, 19 to 27 deg.C
¤ GE-644.2 ASTM THERMOMETER 18 C, 34 to 42 deg.C
¤ GE-644.3 ASTM THERMOMETER 19 C, 49 to 57 deg.C
¤ GE-644.4 ASTM THERMOMETER 20 C, 57 to 65 deg.C
¤ GE-644.5 ASTM THERMOMETER 21 C, 79 to 87 deg.C
¤ GE-644.6 ASTM THERMOMETER 22 C, 95 to 103 deg.C
¤ BI-200 FLASH AND FIRE POINT BY CLEVELAND OPEN CUP ( ASTM D-92, AASHTO T-48)
¤ BI-200 A FLASH AND FIRE POINT BY CLEVELAND OPEN CUP ( ASTM D-92, AASHTO T-48)
¤ BI-210 SOFTENING POINT TEST SET ( ASTM D-36, AASHTO T-53)
¤ BI-220 LOSS ON HEATING / THIN-FILM TEST ( ASTM D-6/ D-1754, AAHSTO T-47/ T-179)
¤ BI-230 LABORATORY PENETRATION TEST SET ( ASTM D-5 / AASHTO T-49)
¤ BI-230 A LABORATORY PENETRATION TEST SET ( ASTM D-5 / AASHTO T-49)
¤ BI-250 DUCTILITY OF BITUMINOUS MATERIALS TEST SET ( ASTM D-113, AASHTO T-51)
¤ BI-300 CENTRIFUGE EXTRACTOR TEST SET ( ASTM D-2172, AASHTO T-164)
¤ BI-300 A CENTRIFUGE EXTRACTOR TEST SET ( ASTM D-2172, AASHTO T-164)
¤ BI-310 REFLUX EXTRACTOR TEST SET ( ASTM D-2172, AASHTO T-164)
¤ BI-320 MARSHALL TEST SET ( ASTM D-1559, AASHTO T-245)
¤ BI-400 CORE DRILLING TEST SET
¤ BI-450 BENKLEMAN BEAM
¤ BI-470 MOT STRAIGHT EDGE
MISCELLANEOUS
¤ UTM-1000WE UNIVERSAL TESTING MACHINE ( 1000 kN)
¤ MI-100 TENSILE TESTING MACHINE, test of PVC materials.
¤ MI-120 DIBBLE ( TUGAL)
¤ MI-130 RAIN GAUGE
GENERAL EQUIPMENT ( Alat Uji Penunjang)
¤ GE-101.1 PROVING RIN G, 100 kg capacity.
¤ GE-101.2 Proving Ring, 250 lbs capacity.
¤ GE-101.3 Proving Ring, 500 lbs capacity.
¤ GE-101.4 Proving Ring, 1.000 lbs capacity.
¤ GE-101.5 Proving Ring, 2.000 lbs capacity.
¤ GE-101.6 Proving Ring, 6.000 lbs capacity.
¤ GE-101.7 Proving Ring, 10.000 lbs capacity.
¤ GE-130 Dial Indicator, 0.2 in. x 0.0001 in.
¤ GE-131 Dial Indicator, 1.0 in. x 0.01 in.
¤ GE-135 Dial Indicator, 10 mm x 0.01 mm
¤ GE-136 Dial Indicator, 20 mm x 0.01 mm
¤ GE-137 Dial Indicator, 30 mm x 0.01 mm
¤ GE-138 Dial Indicator, 50 mm x 0.01 mm
¤ GE-140 Magnetic Dial Holder
¤ GE-150 CENT O-GRAM BALANCE, 311 gr cap x 0.01 sensitivity.
¤ GE-152 TRIPLE BEAM BALANCE, 2610 gr cap x 0.1 sensitivity.
¤ GE-153 DIAL O- GRAM BALANCE, 2610 gr cap x 0.1 sensitivity.
¤ GE-157 HEAVY DUTY SOLUTION BALANCE, 20 kg cap x 1 sensitivity.
¤ GE-159 PLATFORM SCALE, 50 kg cap x 10 gr sensitivity,
¤ GE-160 DIGITAL BALANCE, 310 gr cap x 0.001 gr sensitivity.
GE-161 DIGITAL BALANCE, 6100 gr cap x 0.1 gr sensitivity.
¤ GE-171 OVEN, 14 litre, drying type
¤ GE-172 OVEN, 32 litre, drying type
¤ GE-173 OVEN, 39 litre, drying type
¤ GE-174 OVEN, 53 litre, drying type
¤ GE-175 OVEN, 108 litre, drying type
¤ GE-176 OVEN, 256 litre, drying type
¤ GE-177 OVEN, 416 litre, drying type
¤ GE-178 OVEN, 749 litre, drying type
¤ GE-191 HOT PLATE, Single burner plate.
¤ GE-192 HOT PLATE, Double burner plate.
¤ GE-396 GLASS PLATE, 10 mm thick, 30 x 30 cm.
¤ WATER BATH, COOLING SYSTEM
¤ BUTANE FIELD HEATER, BUNSEN BURNER, STATIF, TRIPOD STAND, GLASS CLAMP, ASBESTOS WIRE GAUZE
¤ SQUARE PAN, 25 x 25 x 5 cm; 40 x 40 x 5 cm; 50 x 50 x 7.5 cm; 65 x 65 x 7.5 cm.
¤ RECTANGULAR PAN, 30 x 20 x 10 cm; 45 x 30 x 15 cm; 60 x 40 x 25 cm.
¤ THIN BOX, ROUND PAN; SAMPLE CAN
¤ MIXING BOWL, 10cm - 20cm - 24cm diameter.
¤ GRADUATED CYLINDER, Glass, 25 ml, 50 ml, 100 ml, 250 ml, 500 ml, 1000 ml capacity.
¤ GRADUATED CYLINDER, Plastic, 25 ml, 50 ml, 100 ml, 250 ml, 500 ml, 1000 ml capacity.
¤ VOLUMETRIC FLASK, 100 ml, 250 ml, 500 ml, 1000 ml capacity.
¤ BEAKER GLASS, 100 ml, 250 ml, 600 ml, 800 ml, 1000 ml capacity.
¤ ERLENMEYAR FLASK, 125 ml, 250 ml, 500 ml, 1000 ml, 2000 ml capacity.
¤ VACUUM FLASK, 125 ml, 250 ml, 500 ml, 1000 ml, 2000 ml capacity.
¤ DENSITY BOTTLE, Glass 50 ml - 100 ml capacity.
¤ SEPARATORY FUNNEL, Glass, 250 ml - 500 ml capacity.
¤ FILTER FUNNEL, Porcelain, 125 ml - 500 ml capacity.
¤ DESSICATOR, Non vacuum, silica gel, 21 cm -24 cm - 30 cm diameter.
¤ DESSICATOR, Vacuum type, silica gel, 21 cm -24 cm - 30 cm diameter.
¤ FUNNEL, plastic or glass, wide or narrow mouth.
¤ BURRETE, , 10 ml, 25 ml, 50 ml, 100 ml capacity.
¤ EVAPORATING DISH, 9 cm dia - 100 ml capacity; 12 cm dia - 250 ml capacity; 15 cm dia - 350 ml capacity; 17 cm dia., 500 ml capacity.
¤ MORTAR & PASTLE, 12 cm - 15 cm- 18 cm diameter.
¤ WASH BOTTLE, 250 ml - 500 ml - 1000 ml capacity.
¤ PIPETTE, 5 ml - 10 ml capacity
¤ CRUCIBLE, 13 ml - 18 ml - 25 ml - 40 ml capacity.
¤ THERMOMETER, range 0 - 50 deg.C; 0 - 100 deg.C; 0 - 150 deg.C; 0 - 200 deg.C; 0 - 300 deg.C. 0 - 360 deg.C.
¤ POCKET DIAL THERMOMETER, range 0 - 100; 0 - 200; 0 - 300 deg.C.
¤ DIAL THERMOMETER, range 0 - 100; 0 - 200; 0 - 300 deg.C.
¤ GE-641 ASTM THERMOMETER 12 C, 20 to 102 deg.C ( Specific Gravity)
¤ GE-642 ASTM THERMOMETER 63 C, 8 to 32 deg.C.
¤ GE-643 ASTM THERMOMETER 13 C, 155 to 170 deg.C ( Loss on Heating)
¤ GE-646.1 ASTM THERMOMETER 15 C, 15 C, 2 to 80 deg.C ( Softening Point)
¤ GE-646.2 ASTM THERMOMETER 16 C, 30 to 200 deg.C ( Softening Point)
¤ GE-648 ASTM THERMOMETER 11 C, 6 to 400 deg.C ( Open Flash)
¤ GE-649.1 ASTM THERMOMETER 7 C, 2 to 300 deg.C ( Distilation)
¤ GE-649.2 ASTM THERMOMETER 8 C, 2 to 400 deg.C ( Distilation)
¤ GE-670 MANOMETER, 25 kg/ cm2 capacity, 6 " dia.
¤ GE-671 MANOMETER, 60 kg/ cm2 capacity, 6 " dia.
¤ GE-672 MANOMETER, 150 kg/ cm2 capacity, 6 " dia.
¤ GE-673 MANOMETER, 250 kg/ cm2 capacity, 6 " dia.
¤ GE-674 MANOMETER, 300 kg/ cm2 capacity, 6 " dia.
¤ GE-675 MANOMETER, 500 kg/ cm2 capacity, 6 " dia.
¤ GE-676 MANOMETER, 700 kg/ cm2 capacity, 6 " dia.
¤ GE-677 MANOMETER, 1000 kg/ cm2 capacity, 6 " dia.
¤ GE-679 VACUUM MANOMETER, 4 " dia. 0-76 cm HG.
¤ GE-680 VACUUM PUMP, Rotary type, 1/ 2 HP,
¤ HYDRAULIC CYLINDER, 30 - 50 - 100 - 150 - 200 - Ton capacity.
¤ GE-690 HYDRAULIC HAND PUMP, 10.000 psi, single acting.
¤ GE-691 HYDRAULIC HAND PUMP, 10.000 psi, double acting.
¤ GE-694 HYDRAULIC ELECTRIC PUMP, 10.000 psi, single acting.
¤ GE-695 HYDRAULIC ELECTRIC PUMP, 10.000 psi, double acting.
¤ GE-697 HYDRAULIC HOSE, 100 - 200 cm length, 10.000 psi.
¤ GE-700 STOP WATCH, 60 sec sweep x 30 min.
¤ GE-701 STOP WATCH, 30 sec sweep x 30 min.
¤ GE-710 VERNIER CALIPER, 6 inch ( 150 mm) range measuring.
¤ GE-711 VERNIER CALIPER, 8 inch ( 200 mm) range measuring.
¤ GE-712 VERNIER CALIPER, 10 inch ( 250 mm) range measuring.
¤ GE-713 VERNIER CALIPER, 12 inch ( 300 mm) range measuring.
¤ Levels, Open End Wrench, Ring Spanner, Allen Key, Pipe Wrench, Strap Wrench, Adjustable Wrench,
¤ Rubber Gloves, Leather Gloves, Asbestos Gloves, Quatering Canvas.
¤ Round Scoop, Flat Scoop, Scoop Pan, Aggregate Scoop. Round Scoop, Flat Scoop, Scoop Pan, Aggregate Scoop.
¤ GE-820 Spatula, Scraper, Wire Saw, Spoon, Trowel, Gardener' s Type Trowel, Chissel, Ruler, Rubber Mallet, Steel Wire Brush, Brass Wire Brush, Soft Brush, Tamping Rod, Straight Edge.
¤ GE-950TW MORTAR MIXER, Bench model; 5 litre capacity.
Anda bisa mengklik " Info Perusahaan " , " Katalog Produk " dan " Hubungi Kami " untuk melihat isi dan informasi lain dari situs CV. RUNDAWA TEKNIK HUB 081320384243 , 02292261057 . . .